High-Performance PTO Shaft for Hose Reel Applications
の hose reel irrigator トラクターのPTO出力からの一定の回転エネルギーの流れを利用して、その作動機構を駆動します。 PTO shaft for hose reel irrigator is designed to meet the demanding torque profiles and operational rhythms of travelling irrigation. Built for Australian conditions and available through ptoparts.topこのシャフトは、放牧地から放牧地へと、安定した性能を発揮します。
Technical Specifications – Hose Reel PTO Shaft
| パラメータ | 仕様／カスタマイズ可能な範囲 |
|---|---|
| 応用 | Hose Reel |
| 推奨トラクター馬力 | 30～90馬力 |
| PTO速度 | 540 rpm (Economy) |
| 最大連続トルク | 200～600 Nm |
| 最大トルク容量 | 900 Nm |
| シャフトシリーズ | T2 / L2（軽～中負荷）/ T3 / L3（中負荷）/ T4 / L4（中～重負荷） |
| Outer Tube Diameter | 65 mm |
| チューブプロファイル | Square profile or Star profile |
| Maximum Extended Length | 1386 mm |
| Safety Guard Material | HDPE (high-density polyethylene) / Injection-moulded PP (polypropylene) |
| ヨーク素材 | 鍛造合金鋼（42CrMo） |
| 動作温度範囲 | -30°C to +100°C |
| Universal Joint Cross Size | 22×54.8 mm / 34.9×93.1 mm / 23.8×61.3 mm |
| 閉じた状態の長さ（L）ミニ) | 700～1100mm（カスタマイズ可能） |
| ガードカラー | Black |
| 表面処理 | 黄色亜鉛メッキ |
| 推奨潤滑剤 | NLGI #2 multi-purpose |
| トラクターエンドヨークオプション | Plain bore yoke / Splined yoke (1-3/4″ 6-spline) |
| 組み立て重量 | 11–24 kg (varies by length) |
| チューブ壁厚 | 3.0 mm |
Working Principle of the Hose Reel PTO Shaft
At its core, the PTO shaft is a torque conduit. It begins at the tractor’s PTO output—a splined stub rotating at a governed speed—and terminates at the hose reel irrigator’s input flange or spline. Between these two endpoints, the shaft must compensate for three-dimensional movement: fore-aft telescoping, vertical angularity, and lateral offset.
Two Cardan-type universal joints provide the angular flexibility, while the lemon, star, or triangular profile tube slides within its mating tube to manage length changes. In the context of travelling irrigation, this means the shaft continuously adapts as the tractor turns, undulates over terrain, or lifts the implement on its three-point hitch.
The hose reel irrigator receives this rotational input through a gearbox or directly to its functional mechanism. The PTO shaft’s torque limiter acts as a mechanical fuse—if the implement encounters an immovable obstruction, the limiter disengages or absorbs the shock before damage can propagate to the tractor’s drivetrain.
Core Advantages of Our PTO Shaft for Hose Reel
⚙ 合金鋼構造
Our hose reel irrigator PTO shaft uses high-grade alloy steel tubing and forged yokes, offering up to 40% longer service life than economy alternatives.
🔨 クイックフィットヨークオプション
クイックリリース式、プレーンボア式、スプライン式ヨークから選択でき、ほとんどの構成で工具不要で迅速に作業機を交換できます。
🔒 マルチステージ保護
お客様の具体的な運用リスクプロファイルに合わせて、せん断ボルト式、摩擦クラッチ式、またはフリーホイール式オーバーランニングクラッチ式保護装置からお選びください。
⚖ メンテナンスの手間が少ないベアリング
すべてのユニバーサルジョイントに密閉型ニードルローラーベアリングを採用することで、頻繁なグリースアップが不要になり、重荷重下でもスムーズで低摩擦の回転を維持します。
🛠 長さのカスタマイズオプション
標準長さと特注長さのシャフトをご用意しており、当社のシャフトは改造なしでほぼすべてのトラクターと作業機の間隔に適合します。
🌍オーストラリアでテスト済み
すべてのシャフト設計は、市場に出荷される前に、オーストラリアの現場環境（高温、粉塵、長時間稼働など）の下で検証されます。
Brand Compatibility & Replacement Parts
Our PTO shaft for hose reel irrigator is designed as a direct-fit replacement for driveline assemblies supplied by ユーロカードン, ボンディオリ＆パヴェージ, AgriCardan, PTOライン, ウォルターシャイド, ウィーズラー, and others. We stock cross-reference guides to help you identify the correct shaft for your existing equipment.
⚠ Brand names are referenced solely for cross-compatibility identification purposes. We are not affiliated with, nor do we claim endorsement by, any of the brands mentioned. All trademarks remain the property of their respective owners.
Spare Parts & Accessories
Every component of our PTO shaft is available individually: U-joint cross kits, yokes (tractor-end and implement-end), profile tubes, safety guards, guard chains, torque limiters, and bearing kits. This means you can service and rebuild your shaft indefinitely, reducing long-term ownership costs.
Regulations, Compliance & Local SEO Considerations
Australian Safety Standards
All PTO shafts supplied for hose reel irrigator applications comply with AS 1121 (Power take-offs for agricultural tractors) and AS/NZS 4024.1 (Safety of machinery). Safety guards meet the guarding requirements of Safe Work Australia’s model WHS Regulations.
CE & ISO Compliance
Our manufacturing facility holds ISO 9001:2015 certification. Shaft assemblies are designed in accordance with ISO 5673 (Agricultural tractors and machinery – PTO drive shafts) and CE-marked where applicable.
State & Territory Requirements
PTO-driven equipment across Queensland, New South Wales, Victoria, Western Australia, South Australia, and Tasmania must comply with local WHS codes of practice for agricultural machinery. Our shafts are supplied with all required safety guarding and documentation to meet these obligations.
PTO Shaft Selection Guide – Hose Reel
Selecting the right PTO shaft for your hose reel irrigator is straightforward when you follow this step-by-step guide. Gather the information below before placing your order.
| ステップ | アクション | Details for Hose Reel |
|---|---|---|
| 1 | トラクターのPTO馬力を特定する | 標準出力：この用途では30～90馬力 |
| 2 | PTO速度設定を確認してください | 540rpmまたは1000rpm（作業機の取扱説明書をご確認ください） |
| 3 | 閉じた状態の長さ（L）を測定しますミニ) | 700～1100mm |
| 4 | トラクターのPTOスプラインの数を数える | 6スプライン（1-3/8インチ）または6スプライン（1-3/4インチ）が最も一般的 |
| 5 | 実装入力接続を確認してください | スプライン、キー、またはフランジ入力 |
| 6 | トルク要件を計算する | 200～600 Nm |
| 7 | シャフトシリーズを選択してください | T2 / L2（軽～中程度の作業）またはT3 / L3（中程度の作業） |
| 8 | 過負荷保護を選択してください | Friction clutch recommended for hose reel irrigator |
📌 お困りですか？ お問い合わせ 専門家の指導を受けるには。
Targeted Installation Procedure – Hose Reel PTO Shaft
⚠ 安全第一: PTOを解除し、エンジンを停止し、イグニッションキーを抜き、駆動系を作業する前にすべての可動部品が完全に停止するまで待ってください。ぴったりとした衣服や手袋など、適切な個人用保護具（PPE）を着用してください。
フェーズ1：準備
Lay out all shaft components and cross-reference against the packing list. Confirm the shaft series, closed length, and yoke specifications match your hose reel irrigator setup. Grease all U-joint nipples and slide the profile tubes back and forth several times to distribute lubricant.
フェーズ2：長さの検証
With the hose reel irrigator hitched to the tractor in its normal operating position, measure the PTO-to-input distance. The shaft must have a minimum of 1/3 tube overlap at full extension and must not bottom out at the shortest position. Trim the tubes if the factory length requires adjustment (refer to cutting instructions in the product manual).
フェーズ3：トラクター接続
トラクター側のヨークをPTOスタブに完全に押し込みます。クイックリリースカラーが保持溝にカチッとはまるはずです。ヨークを後ろに引いて、ロックされていることを確認してください。プレーンボアヨークを使用する場合は、せん断ピンを挿入し、割りピンで固定します。
フェーズ4：接続の実装
Connect the implement-end yoke to the hose reel irrigator’s input. If a clutch assembly is fitted at this end, ensure the clutch housing is oriented with the grease nipple accessible. Tighten any set screws to the specified torque.
フェーズ5：ガードの取り付け
2つのガード半分をシャフトの周りに組み立てて、クリップで留めます。回転防止チェーンを取り付けます。1つはトラクターの固定ポイントに、もう1つは作業機のフレームに取り付けます。ガードがシャフトやヨークのどの部分にも接触することなく、手で自由に回転することを確認してください。
フェーズ6：運用テスト
Start the tractor, engage PTO at low idle, and run the hose reel irrigator unloaded for two to three minutes. Check for vibration, abnormal noise, or heat at the U-joints. If all checks pass, proceed to normal operating speed and begin field work. Re-torque all fasteners after the initial run-in period.
PTO Shaft Troubleshooting Guide for Hose Reel
⚠ Shaft will not telescope smoothly
考えられる原因： Corrosion or debris in profile tubes; insufficient lubrication
推奨される行動： Clean and grease profile tubes; replace if scoring is visible
⚠ Excessive vibration during operation
考えられる原因： Worn U-joint cross bearings; shaft out of balance; excessive operating angle
推奨される行動： Replace U-joint cross kit; check yoke alignment; reduce operating angle to <25°
⚠ Heat build-up at U-joint
考えられる原因： Insufficient lubrication; excessive operating angle; bearing failure
推奨される行動： Grease U-joints immediately; reduce operating angle; replace cross kit if bearings are damaged
⚠ Clicking or knocking noise at low speed
考えられる原因： Worn U-joint needle bearings; loose yoke on PTO stub
推奨される行動： Replace U-joint assembly; check spline wear and yoke locking mechanism
⚠ Safety guard not rotating freely
考えられる原因： Guard bearings seized; guard damaged or misaligned
推奨される行動： Replace guard bearings; straighten or replace guard halves; re-attach chains correctly
⚠ Implement speed inconsistent
考えられる原因： PTO shaft slipping; worn splines; clutch partially engaged
推奨される行動： Check yoke engagement; replace yoke if splines are worn; adjust or replace clutch assembly
⚠ PTO shaft disconnects during operation
考えられる原因： Worn locking collar; damaged retaining groove on PTO stub
推奨される行動： Replace quick-release yoke; inspect and repair PTO stub groove if worn
⚠ 通常負荷時に過負荷クラッチが滑る
考えられる原因： クラッチプレートの摩耗または汚染、あるいはトルク設定の誤り
推奨される行動： Adjust clutch torque setting; replace clutch plates if worn or oil-contaminated
Case Studies – PTO Shaft for Hose Reel in Australia
Field notes from our engineering and sales team across Australia:
📍 Northam, WA – Phil Bennett
Purpose: Outfitted a newly purchased second-hand hose reel irrigator with a reliable aftermarket PTO shaft
Feedback: “I ordered a replacement cross kit six months later and it arrived within 48 hours. Great product, great service, great support.”
📍 Coffs Harbour, NSW – Sam Thornton
Purpose: Upgraded overload protection from shear bolt to friction clutch for smoother travelling irrigation
Feedback: “Fitted perfectly to my hose reel irrigator with zero modification. The quality is noticeably better than the OEM shaft it replaced. I’ll be ordering more for my other implements.”
📍 Esperance, WA – Rick Dawson
Purpose: Replaced a worn PTO shaft on a 3-year-old hose reel irrigator to restore full operating efficiency
Feedback: “The integrated friction clutch saved my gearbox when we hit a buried rock. The shaft disengaged instantly and re-engaged once the obstruction was cleared. Worth every cent.”
📍 Colac, VIC – Dean Hartley
Purpose: Required a custom-length shaft for a non-standard tractor-to-implement spacing
Feedback: “Fast delivery to regional Australia. The shaft arrived well-packaged and the U-joints are smooth as butter. Very impressed with the build quality.”
📍 Bathurst, NSW – Neil Ferguson
Purpose: Replaced a corroded shaft that had been exposed to chemical spray residues
Feedback: “We run our hose reel irrigator hard across 2,000 hectares and this shaft hasn’t missed a beat after two full seasons. Exceptional value for money.”
Frequently Asked Questions – PTO Shaft for Hose Reel
❓ How do I measure the correct closed length?
Hitch the implement to the tractor in its normal working position. Measure the straight-line distance from the face of the tractor PTO stub to the face of the implement input shaft. The shaft closed length should be approximately 10–15 mm less than this measurement.
❓ What causes premature U-joint failure?
Common causes include insufficient lubrication, excessive operating angles (over 25°), running at speeds higher than rated, misalignment between tractor and implement, and lack of regular inspection. Following the recommended maintenance schedule significantly extends U-joint life.
❓ Do you ship to regional and remote Australia?
Absolutely. We ship to all Australian postcodes via major freight carriers. Regional and remote areas may have slightly longer transit times, but we work with multiple carriers to ensure reliable delivery across the country.
❓ Can the shaft be shortened to fit my setup?
Yes. The telescoping profile tubes can be cut to a shorter length using an angle grinder or chop saw. Ensure a minimum of 1/3 overlap remains between the inner and outer tubes after cutting. Deburr all cut edges before reassembly.
❓ What PTO shaft series do I need for my hose reel irrigator?
For most hose reel irrigator applications in the 30–90 HP range, we recommend the T2 / L2 (Light-medium duty) or T3 / L3 (Medium duty) series. If you operate near the upper end of this range or in particularly demanding conditions, consider stepping up to the S6 (Standard) series for additional safety margin.
❓ How often should I grease the PTO shaft?
Grease all U-joint nipples every 8–10 hours of operation, or at the start of each working day. Grease the telescoping profile tubes at the same interval. Use EP2 lithium-complex grease or as recommended in your product manual.
❓ Will this shaft fit my tractor and hose reel irrigator?
Our PTO shafts are available with all standard yoke types and spline sizes (1-3/8" 6-spline, 1-3/4" 6-spline, 1-3/4" 20-spline, and more). Provide your tractor model and hose reel irrigator make/model, and our team will confirm compatibility before dispatch.
❓ Can I use a 540 rpm shaft on a 1000 rpm PTO?
No. Using a shaft rated for 540 rpm on a 1000 rpm PTO will result in excessive speed, dangerous vibration, and potential catastrophic failure. Always match the shaft speed rating to both the tractor PTO setting and the implement requirement.
Related Products
Complement your Hose Reel PTO shaft with these products from our range:
Partner With Us – Hose Reel PTO Shaft Solutions
Whether you are a farmer seeking a single replacement shaft, a dealer looking to stock reliable driveline products, or an OEM manufacturer requiring bulk supply, we are ready to support your needs. Our hose reel irrigator PTO shafts are available in standard and custom configurations, with competitive pricing for volume orders.
📞 Contact our team today to discuss your requirements, request a quotation, or arrange a technical consultation. We are committed to delivering the right shaft, on time, every time.