PTO Shaft for Sugarcane Planter – Built Tough for Real-World Farming
Real-world farming means unpredictable conditions—uneven terrain, sudden load spikes, long hours, and extreme temperatures. Our PTO shaft for sugarcane planter is engineered with these realities in mind, delivering consistent power for sugarcane sett planting without compromise. Every shaft undergoes rigorous quality inspection before dispatch. Browse our catalogue at ptoparts.top.
Technical Specifications – Sugarcane Planter PTO Shaft
| Parameter | Spesifikasi / Rentang yang Dapat Disesuaikan |
|---|---|
| Aplikasi | Sugarcane Planter |
| Rekomendasi Tenaga Kuda Traktor | 60–180 HP |
| Kecepatan PTO | 1000 rpm |
| Torsi Kontinu Maksimum | 400–1200 Nm |
| Kapasitas Torsi Puncak | 1800 Nm |
| Seri Poros | T4 / L4 (Medium-heavy duty) / T5 / L5 (Heavy duty) / T6 / L6 (Super heavy duty) |
| Kekerasan Spline | HRC 55-60 |
| Kisaran Suhu Operasional | -30°C to +100°C |
| Berat Rakitan | 12–44 kg (varies by length) |
| Warna Penjaga | Orange (RAL 2004) |
| Dynamic Balance | Dynamically balanced to ISO 1940 G16 |
| Opsi Yoke Ujung Implementasi | Splined yoke (1-3/4″ 20-spline) / Splined yoke (1-3/4″ 6-spline) |
| Tube Wall Thickness | 3.5 mm |
| Pelumas yang Direkomendasikan | NLGI #2 multi-purpose |
| Opsi Yoke Ujung Traktor | Double yoke / Splined yoke (1-3/4″ 20-spline) |
| Maximum Extended Length | 1688 mm |
| Bahan Pelindung Keselamatan | Metal-reinforced composite / HDPE (high-density polyethylene) |
| Jenis Bantalan Sambungan U | Rol jarum tertutup |
| Universal Joint Cross Size | 34.9×93.1 mm / 30.2×92 mm / 27×70 mm |
| Profil Tabung | Triangular profile or Star profile |
Understanding PTO Shaft Mechanics for the Sugarcane Planter
In sugarcane sett planting, the sugarcane planter draws all its operating power through the PTO shaft. This shaft is essentially a rotating driveline that connects the tractor’s PTO output to the implement’s working mechanism via a series of universal joints and a telescoping tube.
The tractor-side yoke slides onto the PTO stub (typically 1-3/8" 6-spline or 1-3/4" 6-spline), locking into place. As the PTO engages, the stub begins to rotate, sending power through the shaft. The U-joints at each end allow the shaft to flex as the tractor and sugarcane planter move independently over terrain.
The telescoping section—made from a profiled tube (lemon, star, or triangular cross-section)—slides freely to absorb changes in the distance between tractor and implement. On the sugarcane planter end, the shaft connects to a gearbox or direct-drive mechanism that converts PTO speed and torque into the specific motion needed for sugarcane sett planting.
Core Advantages of Our PTO Shaft for Sugarcane Planter
⚙ Continuous-Duty Rated
Our sugarcane planter PTO shaft is rated for continuous-duty operation, not just intermittent use—critical for high-throughput commercial farming.
🔧 Slip-Clutch Integration
Optional integrated slip clutch within the shaft assembly provides seamless overload protection without external bolt-on devices.
🔒 Shear-Pin Safety
Economy shear-pin option available for cost-sensitive operations, with replacement pins included in every shipment.
⚖ Greaseable Cross Kits
Despite sealed bearings, our crosses include grease nipples for optional periodic lubrication in extreme-duty environments.
🛠 Universal Guard Mounting
Guards fit all standard shaft diameters and include the mounting hardware and chains required for safe installation.
🏆 Technical Support Included
Free driveline engineering consultation with every purchase—our technicians help you select the correct shaft for your exact setup.
Kompatibilitas Merek & Suku Cadang Pengganti
Kita PTO shaft for sugarcane planter dirancang sebagai pengganti langsung untuk rakitan poros penggerak yang dipasok oleh Eurocardan, Shafto, Walterscheid, Bondioli & Pavesi, PTOline, Musangdan lain-lain. Kami menyediakan panduan referensi silang untuk membantu Anda mengidentifikasi poros yang tepat untuk peralatan Anda yang sudah ada.
⚠ Nama merek hanya dirujuk untuk tujuan identifikasi kompatibilitas silang. Kami tidak berafiliasi dengan, dan kami tidak mengklaim dukungan dari, merek-merek yang disebutkan. Semua merek dagang tetap menjadi hak milik dari pemiliknya masing-masing.
Suku Cadang & Aksesoris
Setiap komponen poros PTO kami tersedia secara individual: kit sambungan U, penyangga (ujung traktor dan ujung implement), tabung profil, pelindung keselamatan, rantai pelindung, pembatas torsi, dan kit bantalan. Ini berarti Anda dapat melakukan servis dan perbaikan poros Anda tanpa batas, sehingga mengurangi biaya kepemilikan jangka panjang.
Peraturan, Kepatuhan & Pertimbangan SEO Lokal
Standar Keselamatan Australia
All PTO shafts supplied for sugarcane planter applications comply with AS 1121 (Power take-offs for agricultural tractors) and AS/NZS 4024.1 (Safety of machinery). Safety guards meet the guarding requirements of Safe Work Australia’s model WHS Regulations.
Kepatuhan CE & ISO
Fasilitas manufaktur kami memegang sertifikasi ISO 9001:2015. Rakitan poros dirancang sesuai dengan ISO 5673 (Traktor dan mesin pertanian – poros penggerak PTO) dan diberi tanda CE jika berlaku.
Persyaratan Negara Bagian & Wilayah
Peralatan yang digerakkan PTO di seluruh Queensland, New South Wales, Victoria, Western Australia, South Australia, dan Tasmania harus mematuhi kode praktik K3 setempat untuk mesin pertanian. Poros kami dilengkapi dengan semua pengaman dan dokumentasi keselamatan yang diperlukan untuk memenuhi kewajiban ini.
PTO Shaft Selection Guide – Sugarcane Planter
Selecting the right PTO shaft for your sugarcane planter is straightforward when you follow this step-by-step guide. Gather the information below before placing your order.
| Step | Action | Details for Sugarcane Planter |
|---|---|---|
| 1 | Identify tractor PTO HP | Typical: 60–180 HP for this application |
| 2 | Confirm PTO speed setting | 540 rpm or 1000 rpm (check implement manual) |
| 3 | Measure closed length (Lmin) | 800–1300 mm |
| 4 | Count tractor PTO splines | 6-spline (1-3/8") or 6-spline (1-3/4") most common |
| 5 | Check implement input connection | Splined, keyed, or flanged input |
| 6 | Calculate torque requirement | 400–1200 Nm |
| 7 | Select shaft series | T4 / L4 (Medium-heavy duty) or T5 / L5 (Heavy duty) |
| 8 | Choose overload protection | Friction clutch recommended for sugarcane planter |
📌 Need help? Hubungi kami for expert guidance.
Targeted Installation Procedure – Sugarcane Planter PTO Shaft
⚠ Safety First: Disengage the PTO, switch off the engine, remove the ignition key, and allow all moving parts to come to a complete stop before working on the driveline. Wear appropriate PPE including close-fitting clothing and gloves.
Phase 1: Preparation
Lay out all shaft components and cross-reference against the packing list. Confirm the shaft series, closed length, and yoke specifications match your sugarcane planter setup. Grease all U-joint nipples and slide the profile tubes back and forth several times to distribute lubricant.
Phase 2: Length Verification
With the sugarcane planter hitched to the tractor in its normal operating position, measure the PTO-to-input distance. The shaft must have a minimum of 1/3 tube overlap at full extension and must not bottom out at the shortest position. Trim the tubes if the factory length requires adjustment (refer to cutting instructions in the product manual).
Phase 3: Tractor Connection
Push the tractor-end yoke fully onto the PTO stub. The quick-release collar should snap over the retaining groove. Pull back on the yoke to confirm it is locked. If using a plain-bore yoke, insert the shear pin and secure with a cotter pin.
Phase 4: Implement Connection
Connect the implement-end yoke to the sugarcane planter’s input. If a clutch assembly is fitted at this end, ensure the clutch housing is oriented with the grease nipple accessible. Tighten any set screws to the specified torque.
Phase 5: Guard Fitting
Assemble the two guard halves around the shaft and clip together. Attach the anti-rotation chains: one chain to a stationary tractor point, one chain to the implement frame. Verify the guards spin freely by hand without contacting any part of the shaft or yokes.
Phase 6: Operational Test
Start the tractor, engage PTO at low idle, and run the sugarcane planter unloaded for two to three minutes. Check for vibration, abnormal noise, or heat at the U-joints. If all checks pass, proceed to normal operating speed and begin field work. Re-torque all fasteners after the initial run-in period.
PTO Shaft Troubleshooting Guide for Sugarcane Planter
⚠ Unusual whining or grinding sound
Possible Cause: Kerusakan bantalan input gearbox; poros tidak sejajar
Recommended Action: Periksa kotak roda gigi alat pertanian; sejajarkan kembali traktor dan alat pertanian; periksa tumpang tindih panjang poros.
⚠ Excessive vibration during operation
Possible Cause: Worn U-joint cross bearings; shaft out of balance; excessive operating angle
Recommended Action: Replace U-joint cross kit; check yoke alignment; reduce operating angle to <25°
⚠ Overload clutch slipping under normal load
Possible Cause: Clutch plates worn or contaminated; incorrect torque setting
Recommended Action: Adjust clutch torque setting; replace clutch plates if worn or oil-contaminated
⚠ Shaft will not telescope smoothly
Possible Cause: Korosi atau kotoran di dalam tabung profil; pelumasan yang tidak memadai.
Recommended Action: Bersihkan dan lumasi tabung profil; ganti jika terlihat goresan.
⚠ Implement speed inconsistent
Possible Cause: Poros PTO selip; spline aus; kopling terhubung sebagian
Recommended Action: Periksa pengait poros; ganti poros jika alur aus; setel atau ganti rakitan kopling.
⚠ Shear bolt breaks repeatedly
Possible Cause: Penyumbatan tidak diatasi; jenis baut yang digunakan salah; ukuran poros terlalu kecil
Recommended Action: Bersihkan sumber penyumbatan; gunakan hanya baut dengan mutu yang ditentukan; pertimbangkan untuk mengganti ke seri poros berikutnya.
⚠ Heat build-up at U-joint
Possible Cause: Pelumasan tidak memadai; sudut operasi berlebihan; kerusakan bantalan.
Recommended Action: Segera lumasi sambungan U; kurangi sudut pengoperasian; ganti kit silang jika bantalan rusak.
⚠ PTO shaft disconnects during operation
Possible Cause: Kerah pengunci aus; alur penahan pada poros PTO rusak.
Recommended Action: Ganti dudukan pelepas cepat; periksa dan perbaiki alur poros PTO jika aus.
Case Studies – PTO Shaft for Sugarcane Planter in Australia
Catatan lapangan dari tim teknik dan penjualan kami di seluruh Australia:
📍 Hobart, TAS – Chris Taylor
Tujuan: Upgraded from a light-duty shaft to a heavy-duty series for commercial-scale sugarcane sett planting
Masukan: “Kopling gesek terintegrasi menyelamatkan gearbox saya ketika kami menabrak batu yang terkubur. Poros langsung terlepas dan terhubung kembali setelah halangan teratasi. Sangat berharga.”
📍 Katanning, WA – Sam Thornton
Tujuan: Membeli satu set lengkap poros PTO sebagai suku cadang untuk musim sibuk.
Masukan: “Saya memesan kit pengganti enam bulan kemudian dan tiba dalam waktu 48 jam. Produk hebat, layanan hebat, dukungan hebat.”
📍 Longreach, QLD – Robert Wilson
Tujuan: Outfitted a newly purchased second-hand sugarcane planter with a reliable aftermarket PTO shaft
Masukan: “We run our sugarcane planter hard across 2,000 hectares and this shaft hasn’t missed a beat after two full seasons. Exceptional value for money.”
📍 Coffs Harbour, NSW – Steven Harris
Tujuan: Upgraded overload protection from shear bolt to friction clutch for smoother sugarcane sett planting
Masukan: “We swapped out our old economy shaft for this one and noticed an immediate reduction in vibration. The tractor runs quieter and the implement operates smoother.”
📍 Roma, QLD – Ben Callahan
Tujuan: Mengganti poros yang berkarat akibat terpapar residu semprotan bahan kimia.
Masukan: “The safety guards are solid and rotate freely. They actually meet the WHS requirements unlike the cheap ones you get from other suppliers.”
Frequently Asked Questions – PTO Shaft for Sugarcane Planter
❓ Can I use a 540 rpm shaft on a 1000 rpm PTO?
No. Using a shaft rated for 540 rpm on a 1000 rpm PTO will result in excessive speed, dangerous vibration, and potential catastrophic failure. Always match the shaft speed rating to both the tractor PTO setting and the implement requirement.
❓ Apakah poros PTO Anda seimbang?
Ya. Semua rakitan poros PTO kami diseimbangkan secara dinamis selama proses pembuatan. Hal ini mengurangi getaran, memperpanjang umur bantalan, dan memberikan pengoperasian yang lebih halus dibandingkan dengan alternatif aftermarket yang tidak seimbang.
❓ Apa penyebab kegagalan sambungan U-joint sebelum waktunya?
Penyebab umum meliputi pelumasan yang tidak memadai, sudut pengoperasian yang berlebihan (lebih dari 25°), pengoperasian pada kecepatan lebih tinggi dari yang ditentukan, ketidaksejajaran antara traktor dan alat pertanian, dan kurangnya inspeksi rutin. Mengikuti jadwal perawatan yang direkomendasikan secara signifikan memperpanjang masa pakai sambungan U.
❓ Garansi apa yang Anda tawarkan untuk poros PTO?
Semua poros PTO memiliki garansi pabrik terhadap cacat material dan pengerjaan. Ketentuan garansi berbeda-beda tergantung serinya. Hubungi tim kami untuk detail garansi spesifik yang berlaku untuk pembelian Anda.
❓ Seberapa sering saya harus melumasi poros PTO?
Lumasi semua nipel sambungan U setiap 8–10 jam pengoperasian, atau di awal setiap hari kerja. Lumasi tabung profil teleskopik pada interval yang sama. Gunakan gemuk kompleks litium EP2 atau seperti yang direkomendasikan dalam manual produk Anda.
❓ Will this shaft fit my tractor and sugarcane planter?
Our PTO shafts are available with all standard yoke types and spline sizes (1-3/8" 6-spline, 1-3/4" 6-spline, 1-3/4" 20-spline, and more). Provide your tractor model and sugarcane planter make/model, and our team will confirm compatibility before dispatch.
❓ Apa perbedaan antara baut geser dan kopling gesek?
Baut geser adalah pin pengorbanan yang patah ketika torsi melebihi kapasitas nominalnya. Harganya murah tetapi memerlukan penggantian manual setelah setiap kejadian. Kopling gesek selip ketika kelebihan beban dan secara otomatis terhubung kembali ketika kelebihan beban hilang, menawarkan pengoperasian tanpa gangguan dalam aplikasi yang rentan terhadap beban kejut yang sering terjadi.
❓ Bagaimana cara mengukur panjang tertutup yang tepat?
Pasang alat pertanian ke traktor pada posisi kerja normalnya. Ukur jarak garis lurus dari permukaan poros PTO traktor ke permukaan poros input alat pertanian. Panjang poros saat tertutup harus sekitar 10–15 mm lebih pendek dari pengukuran ini.
Produk Terkait
Complement your Sugarcane Planter PTO shaft with these products from our range:
Partner With Us – Sugarcane Planter PTO Shaft Solutions
Whether you are a farmer seeking a single replacement shaft, a dealer looking to stock reliable driveline products, or an OEM manufacturer requiring bulk supply, we are ready to support your needs. Our sugarcane planter PTO shafts are available in standard and custom configurations, with competitive pricing for volume orders.
📞 Hubungi tim kami hari ini Untuk mendiskusikan kebutuhan Anda, meminta penawaran harga, atau mengatur konsultasi teknis. Kami berkomitmen untuk memberikan poros yang tepat, tepat waktu, setiap saat.