Industrial-Grade PTO Shaft for Seed/Fertilizer Drill Equipment
When combined seed and fertilizer placement is your business, downtime is not an option. Our industrial-grade PTO shaft for seed drill is manufactured from high-strength alloy steel with induction-hardened splines and needle-bearing universal joints. Designed for the rigorous duty cycles of commercial farming, this shaft maintains peak torque delivery while protecting both tractor and implement from shock loads.
Technical Specifications – Seed/Fertilizer Drill PTO Shaft
| Parameter | Spesifikasi / Rentang yang Dapat Disesuaikan |
|---|---|
| Aplikasi | Seed/Fertilizer Drill |
| Rekomendasi Tenaga Kuda Traktor | 30–90 HP |
| Kecepatan PTO | 540/1000 rpm |
| Torsi Kontinu Maksimum | 200–600 Nm |
| Kapasitas Torsi Puncak | 900 Nm |
| Seri Poros | T2 / L2 (Light-medium duty) / T3 / L3 (Medium duty) / T4 / L4 (Medium-heavy duty) |
| Maximum Extended Length | 1367 mm |
| Berat Rakitan | 13–30 kg (varies by length) |
| Dynamic Balance | Dynamically balanced to ISO 1940 G16 |
| Kekerasan Spline | HRC 58-62 |
| Perawatan Permukaan | Black oxide coated |
| Profil Tabung | Star profile or Square profile |
| Opsi Yoke Ujung Traktor | Plain bore yoke / Double yoke |
| Diameter Tabung Luar | 65 mm |
| Kisaran Suhu Operasional | -30°C to +100°C |
| Warna Penjaga | Orange (RAL 2004) |
| Jenis Bantalan Sambungan U | Greased needle roller |
| Opsi Yoke Ujung Implementasi | Double yoke / Quick-release yoke |
| Tube Wall Thickness | 4.5 mm |
| Sudut Operasi Maksimum | 45° |
PTO Shaft Structure & Function on the Seed/Fertilizer Drill
The power take-off (PTO) shaft is positioned between the rear of the tractor and the front input of the seed drill. It is a two-piece telescoping assembly connected by universal joints at each end. The tractor-end yoke mates with the PTO stub shaft, while the implement-end yoke connects to the seed drill’s gearbox input.
When engaged, rotational power flows from the tractor’s engine through the PTO gearbox, out the stub, through the first U-joint, along the profile tube, through the second U-joint, and into the implement. During combined seed and fertilizer placement, this power drives the cutting, turning, or processing mechanism of the seed drill.
Komponen struktural utama meliputi: poros beralur yang diperkeras untuk pengikatan yang positif, sambungan U bantalan jarum untuk rotasi yang mulus di bawah beban, tabung teleskopik untuk penyesuaian panjang, pelindung keselamatan plastik dengan rotasi yang didukung bantalan, dan kopling beban berlebih atau pin geser untuk melindungi seluruh sistem penggerak dari kegagalan fatal.
Core Advantages of Our PTO Shaft for Seed/Fertilizer Drill
⚙ Teknologi Yoke Tempa
Unlike stamped alternatives, our forged yokes for the seed drill PTO shaft deliver superior grain structure and impact resistance for demanding applications.
🔧 Opsi Sambungan Sudut Lebar
Sambungan kecepatan konstan sudut lebar tersedia untuk aplikasi yang membutuhkan sudut operasi hingga 80°, ideal untuk radius putar yang sempit dan medan yang curam.
🔒 Pengaktifan Ulang Otomatis
Model kopling gesek akan secara otomatis terhubung kembali setelah kondisi beban berlebih hilang, meminimalkan waktu henti dan mempercepat pemulihan operasional Anda.
⚖ Lapisan Anti Korosi
Perangkat keras berlapis seng dan pelindung berlapis bubuk tahan terhadap korosi akibat bahan kimia pertanian, kelembapan, dan paparan sinar UV.
🛠 Kompatibilitas Metrik & Imperial
Opsi spline standar ganda memastikan kompatibilitas dengan poros PTO metrik dan imperial di semua merek traktor utama.
🏆 Sertifikasi Kualitas Global
Manufaktur bersertifikasi ISO 9001:2015 dengan ketelusuran material lengkap mulai dari baja mentah hingga produk jadi.
Cross-Compatibility & Replacement Fit Guide
This PTO shaft is engineered to replace OEM and aftermarket drivelines fitted to seed drill equipment from Profil Terhubung, GKN Walterscheid, Walterscheid, Shafto, Driveline Parts, Musang, among others. Our technical team can cross-reference your existing part number to ensure a precise match.
⚠ The use of brand names above is for the sole purpose of assisting customers in identifying compatible replacement parts. No affiliation with or endorsement by any listed brand is implied. All trademarks belong to their respective owners.
Individual Components & Spares
We supply every PTO shaft component separately—cross kits, yoke assemblies, inner and outer tubes, guard sets, clutch assemblies, shear pins, and mounting hardware—so you can rebuild or reconfigure your shaft as needed without purchasing a full replacement.
Regulatory Compliance & Regional Information
Work Health & Safety (WHS)
In Australia, PTO shaft guarding is mandated under the model Work Health and Safety Regulations. Every PTO shaft we supply for seed drill use includes a full-length safety guard assembly, meeting the requirements outlined in the Managing the Risks of Plant in the Workplace Code of Practice.
International Standards
Our products are manufactured to ISO 5673-1 and ISO 5673-2 specifications for PTO driveline dimensions and guarding. Universal joints conform to DIN 71752 for cross and bearing cup tolerances.
Import & Customs
PTO shafts and components are classified under Australian Customs Tariff heading 8483 (transmission shafts and cranks; bearing housings; gears and gearing). Duty rates and GST apply at the time of import. We handle all customs documentation for Australian deliveries.
PTO Shaft Selection Guide – Seed/Fertilizer Drill
Selecting the right PTO shaft for your seed drill is straightforward when you follow this step-by-step guide. Gather the information below before placing your order.
| Step | Action | Details for Seed/Fertilizer Drill |
|---|---|---|
| 1 | Identify tractor PTO HP | Typical: 30–90 HP for this application |
| 2 | Confirm PTO speed setting | 540 rpm or 1000 rpm (check implement manual) |
| 3 | Measure closed length (Lmin) | 700–1100 mm |
| 4 | Count tractor PTO splines | 6-spline (1-3/8") or 6-spline (1-3/4") most common |
| 5 | Check implement input connection | Splined, keyed, or flanged input |
| 6 | Calculate torque requirement | 200–600 Nm |
| 7 | Select shaft series | T2 / L2 (Light-medium duty) or T3 / L3 (Medium duty) |
| 8 | Choose overload protection | Friction clutch recommended for seed drill |
📌 Need help? Hubungi kami for expert guidance.
Targeted Installation Procedure – Seed/Fertilizer Drill PTO Shaft
⚠ Safety First: Disengage the PTO, switch off the engine, remove the ignition key, and allow all moving parts to come to a complete stop before working on the driveline. Wear appropriate PPE including close-fitting clothing and gloves.
Phase 1: Preparation
Lay out all shaft components and cross-reference against the packing list. Confirm the shaft series, closed length, and yoke specifications match your seed drill setup. Grease all U-joint nipples and slide the profile tubes back and forth several times to distribute lubricant.
Phase 2: Length Verification
With the seed drill hitched to the tractor in its normal operating position, measure the PTO-to-input distance. The shaft must have a minimum of 1/3 tube overlap at full extension and must not bottom out at the shortest position. Trim the tubes if the factory length requires adjustment (refer to cutting instructions in the product manual).
Phase 3: Tractor Connection
Push the tractor-end yoke fully onto the PTO stub. The quick-release collar should snap over the retaining groove. Pull back on the yoke to confirm it is locked. If using a plain-bore yoke, insert the shear pin and secure with a cotter pin.
Phase 4: Implement Connection
Connect the implement-end yoke to the seed drill’s input. If a clutch assembly is fitted at this end, ensure the clutch housing is oriented with the grease nipple accessible. Tighten any set screws to the specified torque.
Phase 5: Guard Fitting
Assemble the two guard halves around the shaft and clip together. Attach the anti-rotation chains: one chain to a stationary tractor point, one chain to the implement frame. Verify the guards spin freely by hand without contacting any part of the shaft or yokes.
Phase 6: Operational Test
Start the tractor, engage PTO at low idle, and run the seed drill unloaded for two to three minutes. Check for vibration, abnormal noise, or heat at the U-joints. If all checks pass, proceed to normal operating speed and begin field work. Re-torque all fasteners after the initial run-in period.
PTO Shaft Troubleshooting Guide for Seed/Fertilizer Drill
⚠ PTO shaft disconnects during operation
Possible Cause: Kerah pengunci aus; alur penahan pada poros PTO rusak.
Recommended Action: Ganti dudukan pelepas cepat; periksa dan perbaiki alur poros PTO jika aus.
⚠ Overload clutch slipping under normal load
Possible Cause: Clutch plates worn or contaminated; incorrect torque setting
Recommended Action: Adjust clutch torque setting; replace clutch plates if worn or oil-contaminated
⚠ Safety guard not rotating freely
Possible Cause: Bantalan pelindung macet; pelindung rusak atau tidak sejajar
Recommended Action: Ganti bantalan pelindung; luruskan atau ganti bagian pelindung; pasang kembali rantai dengan benar.
⚠ Implement speed inconsistent
Possible Cause: Poros PTO selip; spline aus; kopling terhubung sebagian
Recommended Action: Periksa pengait poros; ganti poros jika alur aus; setel atau ganti rakitan kopling.
⚠ Clicking or knocking noise at low speed
Possible Cause: Bantalan jarum sambungan U aus; dudukan longgar pada poros PTO
Recommended Action: Ganti rakitan sambungan U; periksa keausan spline dan mekanisme penguncian yoke.
⚠ Excessive vibration during operation
Possible Cause: Worn U-joint cross bearings; shaft out of balance; excessive operating angle
Recommended Action: Replace U-joint cross kit; check yoke alignment; reduce operating angle to <25°
⚠ Heat build-up at U-joint
Possible Cause: Pelumasan tidak memadai; sudut operasi berlebihan; kerusakan bantalan.
Recommended Action: Segera lumasi sambungan U; kurangi sudut pengoperasian; ganti kit silang jika bantalan rusak.
⚠ Shear bolt breaks repeatedly
Possible Cause: Penyumbatan tidak diatasi; jenis baut yang digunakan salah; ukuran poros terlalu kecil
Recommended Action: Bersihkan sumber penyumbatan; gunakan hanya baut dengan mutu yang ditentukan; pertimbangkan untuk mengganti ke seri poros berikutnya.
Case Studies – PTO Shaft for Seed/Fertilizer Drill in Australia
Catatan lapangan dari tim teknik dan penjualan kami di seluruh Australia:
📍 Hobart, TAS – Geoff Lawson
Tujuan: Upgraded from a light-duty shaft to a heavy-duty series for commercial-scale combined seed and fertilizer placement
Masukan: “We run our seed drill hard across 2,000 hectares and this shaft hasn’t missed a beat after two full seasons. Exceptional value for money.”
📍 Devonport, TAS – Phil Bennett
Tujuan: Needed a direct-fit replacement after the original shaft suffered a U-joint failure mid-season
Masukan: “Fitted perfectly to my seed drill with zero modification. The quality is noticeably better than the OEM shaft it replaced. I’ll be ordering more for my other implements.”
📍 Roma, QLD – Neville Grant
Tujuan: Replaced a worn PTO shaft on a 3-year-old seed drill to restore full operating efficiency
Masukan: “Saya memesan kit pengganti enam bulan kemudian dan tiba dalam waktu 48 jam. Produk hebat, layanan hebat, dukungan hebat.”
📍 Albany, WA – Paul Walker
Tujuan: Mengganti poros yang berkarat akibat terpapar residu semprotan bahan kimia.
Masukan: “Mekanik kami terkesan dengan presisi alur dan kualitas bantalan jarumnya. Dia mengatakan ini adalah poros aftermarket terbaik yang pernah dipasangnya dalam 20 tahun.”
📍 Wagga Wagga, NSW – Trevor Collins
Tujuan: Membeli satu set lengkap poros PTO sebagai suku cadang untuk musim sibuk.
Masukan: “Kopling gesek terintegrasi menyelamatkan gearbox saya ketika kami menabrak batu yang terkubur. Poros langsung terlepas dan terhubung kembali setelah halangan teratasi. Sangat berharga.”
Frequently Asked Questions – PTO Shaft for Seed/Fertilizer Drill
❓ What PTO shaft series do I need for my seed drill?
For most seed drill applications in the 30–90 HP range, we recommend the T2 / L2 (Light-medium duty) or T3 / L3 (Medium duty) series. If you operate near the upper end of this range or in particularly demanding conditions, consider stepping up to the S6 (Standard) series for additional safety margin.
❓ Apa penyebab kegagalan sambungan U-joint sebelum waktunya?
Penyebab umum meliputi pelumasan yang tidak memadai, sudut pengoperasian yang berlebihan (lebih dari 25°), pengoperasian pada kecepatan lebih tinggi dari yang ditentukan, ketidaksejajaran antara traktor dan alat pertanian, dan kurangnya inspeksi rutin. Mengikuti jadwal perawatan yang direkomendasikan secara signifikan memperpanjang masa pakai sambungan U.
❓ Bagaimana cara mengukur panjang tertutup yang tepat?
Pasang alat pertanian ke traktor pada posisi kerja normalnya. Ukur jarak garis lurus dari permukaan poros PTO traktor ke permukaan poros input alat pertanian. Panjang poros saat tertutup harus sekitar 10–15 mm lebih pendek dari pengukuran ini.
❓ Apa perbedaan antara baut geser dan kopling gesek?
Baut geser adalah pin pengorbanan yang patah ketika torsi melebihi kapasitas nominalnya. Harganya murah tetapi memerlukan penggantian manual setelah setiap kejadian. Kopling gesek selip ketika kelebihan beban dan secara otomatis terhubung kembali ketika kelebihan beban hilang, menawarkan pengoperasian tanpa gangguan dalam aplikasi yang rentan terhadap beban kejut yang sering terjadi.
❓ Will this shaft fit my tractor and seed drill?
Our PTO shafts are available with all standard yoke types and spline sizes (1-3/8" 6-spline, 1-3/4" 6-spline, 1-3/4" 20-spline, and more). Provide your tractor model and seed drill make/model, and our team will confirm compatibility before dispatch.
❓ Seberapa sering saya harus melumasi poros PTO?
Lumasi semua nipel sambungan U setiap 8–10 jam pengoperasian, atau di awal setiap hari kerja. Lumasi tabung profil teleskopik pada interval yang sama. Gunakan gemuk kompleks litium EP2 atau seperti yang direkomendasikan dalam manual produk Anda.
❓ Apakah Anda melakukan pengiriman ke wilayah regional dan terpencil di Australia?
Tentu saja. Kami mengirimkan ke semua kode pos Australia melalui perusahaan pengiriman barang utama. Daerah regional dan terpencil mungkin memiliki waktu transit yang sedikit lebih lama, tetapi kami bekerja sama dengan berbagai perusahaan pengiriman untuk memastikan pengiriman yang andal di seluruh negeri.
❓ Apakah poros PTO Anda seimbang?
Ya. Semua rakitan poros PTO kami diseimbangkan secara dinamis selama proses pembuatan. Hal ini mengurangi getaran, memperpanjang umur bantalan, dan memberikan pengoperasian yang lebih halus dibandingkan dengan alternatif aftermarket yang tidak seimbang.
Produk Terkait
Complement your Seed/Fertilizer Drill PTO shaft with these products from our range:
Let’s Work Together – Seed/Fertilizer Drill PTO Shaft Supply
We supply PTO shafts for seed drill applications to individual farmers, agricultural dealers, service workshops, and OEM manufacturers across Australia and internationally. Bulk pricing, custom specifications, and private-label options are available for qualified partners.
Ready to get started? Reach out to our sales and engineering team for personalised service.