Industrial-Grade PTO Shaft for Peanut Harvester Equipment
When groundnut lifting and collection is your business, downtime is not an option. Our industrial-grade PTO shaft for peanut harvester is manufactured from high-strength alloy steel with induction-hardened splines and needle-bearing universal joints. Designed for the rigorous duty cycles of commercial farming, this shaft maintains peak torque delivery while protecting both tractor and implement from shock loads.
Technical Specifications – Peanut Harvester PTO Shaft
| Parameter | Spesifikasi / Rentang yang Dapat Disesuaikan |
|---|---|
| Aplikasi | Peanut Harvester |
| Rekomendasi Tenaga Kuda Traktor | 60–180 HP |
| Kecepatan PTO | 540 rpm |
| Torsi Kontinu Maksimum | 400–1200 Nm |
| Kapasitas Torsi Puncak | 1800 Nm |
| Seri Poros | T4 / L4 (Medium-heavy duty) / T5 / L5 (Heavy duty) / T6 / L6 (Super heavy duty) |
| Yoke Material | Forged carbon steel (C45) |
| Dynamic Balance | Factory balanced |
| Maximum Extended Length | 1674 mm |
| Sudut Operasi Maksimum | 80° |
| Kekerasan Spline | HRC 55-60 |
| Kisaran Suhu Operasional | -30°C to +100°C |
| Perawatan Permukaan | Yellow zinc plated |
| Universal Joint Cross Size | 23.8×61.3 mm / 22×54.8 mm / 27×70 mm |
| Opsi Yoke Ujung Traktor | Splined yoke (1-3/8″ 21-spline) / Splined yoke (1-3/8″ 6-spline) |
| Warna Penjaga | Orange (RAL 2004) |
| Closed Length (Lmin) | 800–1300 mm (customisable) |
| Pelumas yang Direkomendasikan | Kompleks litium EP2 |
| Opsi Perlindungan Beban Berlebih | Free-wheel overrunning clutch / Shear bolt torque limiter / Ratchet torque limiter |
| Profil Tabung | Square profile or Triangular profile |
PTO Shaft Structure & Function on the Peanut Harvester
The power take-off (PTO) shaft is positioned between the rear of the tractor and the front input of the peanut harvester. It is a two-piece telescoping assembly connected by universal joints at each end. The tractor-end yoke mates with the PTO stub shaft, while the implement-end yoke connects to the peanut harvester’s gearbox input.
When engaged, rotational power flows from the tractor’s engine through the PTO gearbox, out the stub, through the first U-joint, along the profile tube, through the second U-joint, and into the implement. During groundnut lifting and collection, this power drives the cutting, turning, or processing mechanism of the peanut harvester.
Komponen struktural utama meliputi: poros beralur yang diperkeras untuk pengikatan yang positif, sambungan U bantalan jarum untuk rotasi yang mulus di bawah beban, tabung teleskopik untuk penyesuaian panjang, pelindung keselamatan plastik dengan rotasi yang didukung bantalan, dan kopling beban berlebih atau pin geser untuk melindungi seluruh sistem penggerak dari kegagalan fatal.
Core Advantages of Our PTO Shaft for Peanut Harvester
⚙ Teknologi Yoke Tempa
Unlike stamped alternatives, our forged yokes for the peanut harvester PTO shaft deliver superior grain structure and impact resistance for demanding applications.
🔧 Opsi Sambungan Sudut Lebar
Sambungan kecepatan konstan sudut lebar tersedia untuk aplikasi yang membutuhkan sudut operasi hingga 80°, ideal untuk radius putar yang sempit dan medan yang curam.
🔒 Pengaktifan Ulang Otomatis
Model kopling gesek akan secara otomatis terhubung kembali setelah kondisi beban berlebih hilang, meminimalkan waktu henti dan mempercepat pemulihan operasional Anda.
⚖ Lapisan Anti Korosi
Perangkat keras berlapis seng dan pelindung berlapis bubuk tahan terhadap korosi akibat bahan kimia pertanian, kelembapan, dan paparan sinar UV.
🛠 Kompatibilitas Metrik & Imperial
Opsi spline standar ganda memastikan kompatibilitas dengan poros PTO metrik dan imperial di semua merek traktor utama.
🏆 Sertifikasi Kualitas Global
Manufaktur bersertifikasi ISO 9001:2015 dengan ketelusuran material lengkap mulai dari baja mentah hingga produk jadi.
Kompatibilitas Merek & Suku Cadang Pengganti
Kita PTO shaft for peanut harvester dirancang sebagai pengganti langsung untuk rakitan poros penggerak yang dipasok oleh GKN Walterscheid, MecLine, Bondioli & Pavesi, Profil Terhubung, Driveline Parts, Walterscheiddan lain-lain. Kami menyediakan panduan referensi silang untuk membantu Anda mengidentifikasi poros yang tepat untuk peralatan Anda yang sudah ada.
⚠ Nama merek hanya dirujuk untuk tujuan identifikasi kompatibilitas silang. Kami tidak berafiliasi dengan, dan kami tidak mengklaim dukungan dari, merek-merek yang disebutkan. Semua merek dagang tetap menjadi hak milik dari pemiliknya masing-masing.
Suku Cadang & Aksesoris
Setiap komponen poros PTO kami tersedia secara individual: kit sambungan U, penyangga (ujung traktor dan ujung implement), tabung profil, pelindung keselamatan, rantai pelindung, pembatas torsi, dan kit bantalan. Ini berarti Anda dapat melakukan servis dan perbaikan poros Anda tanpa batas, sehingga mengurangi biaya kepemilikan jangka panjang.
Peraturan, Kepatuhan & Pertimbangan SEO Lokal
Standar Keselamatan Australia
All PTO shafts supplied for peanut harvester applications comply with AS 1121 (Power take-offs for agricultural tractors) and AS/NZS 4024.1 (Safety of machinery). Safety guards meet the guarding requirements of Safe Work Australia’s model WHS Regulations.
Kepatuhan CE & ISO
Fasilitas manufaktur kami memegang sertifikasi ISO 9001:2015. Rakitan poros dirancang sesuai dengan ISO 5673 (Traktor dan mesin pertanian – poros penggerak PTO) dan diberi tanda CE jika berlaku.
Persyaratan Negara Bagian & Wilayah
Peralatan yang digerakkan PTO di seluruh Queensland, New South Wales, Victoria, Western Australia, South Australia, dan Tasmania harus mematuhi kode praktik K3 setempat untuk mesin pertanian. Poros kami dilengkapi dengan semua pengaman dan dokumentasi keselamatan yang diperlukan untuk memenuhi kewajiban ini.
PTO Shaft Selection Guide – Peanut Harvester
Selecting the right PTO shaft for your peanut harvester is straightforward when you follow this step-by-step guide. Gather the information below before placing your order.
| Step | Action | Details for Peanut Harvester |
|---|---|---|
| 1 | Identify tractor PTO HP | Typical: 60–180 HP for this application |
| 2 | Confirm PTO speed setting | 540 rpm or 1000 rpm (check implement manual) |
| 3 | Measure closed length (Lmin) | 800–1300 mm |
| 4 | Count tractor PTO splines | 6-spline (1-3/8") or 6-spline (1-3/4") most common |
| 5 | Check implement input connection | Splined, keyed, or flanged input |
| 6 | Calculate torque requirement | 400–1200 Nm |
| 7 | Select shaft series | T4 / L4 (Medium-heavy duty) or T5 / L5 (Heavy duty) |
| 8 | Choose overload protection | Friction clutch recommended for peanut harvester |
📌 Need help? Hubungi kami for expert guidance.
Targeted Installation Procedure – Peanut Harvester PTO Shaft
⚠ Safety First: Disengage the PTO, switch off the engine, remove the ignition key, and allow all moving parts to come to a complete stop before working on the driveline. Wear appropriate PPE including close-fitting clothing and gloves.
Phase 1: Preparation
Lay out all shaft components and cross-reference against the packing list. Confirm the shaft series, closed length, and yoke specifications match your peanut harvester setup. Grease all U-joint nipples and slide the profile tubes back and forth several times to distribute lubricant.
Phase 2: Length Verification
With the peanut harvester hitched to the tractor in its normal operating position, measure the PTO-to-input distance. The shaft must have a minimum of 1/3 tube overlap at full extension and must not bottom out at the shortest position. Trim the tubes if the factory length requires adjustment (refer to cutting instructions in the product manual).
Phase 3: Tractor Connection
Push the tractor-end yoke fully onto the PTO stub. The quick-release collar should snap over the retaining groove. Pull back on the yoke to confirm it is locked. If using a plain-bore yoke, insert the shear pin and secure with a cotter pin.
Phase 4: Implement Connection
Connect the implement-end yoke to the peanut harvester’s input. If a clutch assembly is fitted at this end, ensure the clutch housing is oriented with the grease nipple accessible. Tighten any set screws to the specified torque.
Phase 5: Guard Fitting
Assemble the two guard halves around the shaft and clip together. Attach the anti-rotation chains: one chain to a stationary tractor point, one chain to the implement frame. Verify the guards spin freely by hand without contacting any part of the shaft or yokes.
Phase 6: Operational Test
Start the tractor, engage PTO at low idle, and run the peanut harvester unloaded for two to three minutes. Check for vibration, abnormal noise, or heat at the U-joints. If all checks pass, proceed to normal operating speed and begin field work. Re-torque all fasteners after the initial run-in period.
PTO Shaft Troubleshooting Guide for Peanut Harvester
⚠ Overload clutch slipping under normal load
Possible Cause: Clutch plates worn or contaminated; incorrect torque setting
Recommended Action: Adjust clutch torque setting; replace clutch plates if worn or oil-contaminated
⚠ Safety guard not rotating freely
Possible Cause: Bantalan pelindung macet; pelindung rusak atau tidak sejajar
Recommended Action: Ganti bantalan pelindung; luruskan atau ganti bagian pelindung; pasang kembali rantai dengan benar.
⚠ Implement speed inconsistent
Possible Cause: Poros PTO selip; spline aus; kopling terhubung sebagian
Recommended Action: Periksa pengait poros; ganti poros jika alur aus; setel atau ganti rakitan kopling.
⚠ Heat build-up at U-joint
Possible Cause: Pelumasan tidak memadai; sudut operasi berlebihan; kerusakan bantalan.
Recommended Action: Segera lumasi sambungan U; kurangi sudut pengoperasian; ganti kit silang jika bantalan rusak.
⚠ Clicking or knocking noise at low speed
Possible Cause: Bantalan jarum sambungan U aus; dudukan longgar pada poros PTO
Recommended Action: Ganti rakitan sambungan U; periksa keausan spline dan mekanisme penguncian yoke.
⚠ Excessive vibration during operation
Possible Cause: Worn U-joint cross bearings; shaft out of balance; excessive operating angle
Recommended Action: Replace U-joint cross kit; check yoke alignment; reduce operating angle to <25°
⚠ PTO shaft disconnects during operation
Possible Cause: Kerah pengunci aus; alur penahan pada poros PTO rusak.
Recommended Action: Ganti dudukan pelepas cepat; periksa dan perbaiki alur poros PTO jika aus.
⚠ Unusual whining or grinding sound
Possible Cause: Kerusakan bantalan input gearbox; poros tidak sejajar
Recommended Action: Periksa kotak roda gigi alat pertanian; sejajarkan kembali traktor dan alat pertanian; periksa tumpang tindih panjang poros.
Case Studies – PTO Shaft for Peanut Harvester in Australia
Catatan lapangan dari tim teknik dan penjualan kami di seluruh Australia:
📍 Albany, WA – Glen Armstrong
Tujuan: Upgraded overload protection from shear bolt to friction clutch for smoother groundnut lifting and collection
Masukan: “Fitted perfectly to my peanut harvester with zero modification. The quality is noticeably better than the OEM shaft it replaced. I’ll be ordering more for my other implements.”
📍 Esperance, WA – Darren Hughes
Tujuan: Membeli satu set lengkap poros PTO sebagai suku cadang untuk musim sibuk.
Masukan: “Saya memesan kit pengganti enam bulan kemudian dan tiba dalam waktu 48 jam. Produk hebat, layanan hebat, dukungan hebat.”
📍 Merredin, WA – James Mitchell
Tujuan: Replaced a worn PTO shaft on a 3-year-old peanut harvester to restore full operating efficiency
Masukan: “Pengiriman cepat ke wilayah regional Australia. Poros tiba dalam kemasan yang baik dan sambungan U-nya sangat halus. Sangat terkesan dengan kualitas pembuatannya.”
📍 Toowoomba, QLD – Michael Carter
Tujuan: Upgraded from a light-duty shaft to a heavy-duty series for commercial-scale groundnut lifting and collection
Masukan: “We run our peanut harvester hard across 2,000 hectares and this shaft hasn’t missed a beat after two full seasons. Exceptional value for money.”
📍 Dubbo, NSW – Tony Blake
Tujuan: Needed a direct-fit replacement after the original shaft suffered a U-joint failure mid-season
Masukan: “Kopling gesek terintegrasi menyelamatkan gearbox saya ketika kami menabrak batu yang terkubur. Poros langsung terlepas dan terhubung kembali setelah halangan teratasi. Sangat berharga.”
Frequently Asked Questions – PTO Shaft for Peanut Harvester
❓ Apakah Anda melakukan pengiriman ke wilayah regional dan terpencil di Australia?
Tentu saja. Kami mengirimkan ke semua kode pos Australia melalui perusahaan pengiriman barang utama. Daerah regional dan terpencil mungkin memiliki waktu transit yang sedikit lebih lama, tetapi kami bekerja sama dengan berbagai perusahaan pengiriman untuk memastikan pengiriman yang andal di seluruh negeri.
❓ Can the shaft be shortened to fit my setup?
Yes. The telescoping profile tubes can be cut to a shorter length using an angle grinder or chop saw. Ensure a minimum of 1/3 overlap remains between the inner and outer tubes after cutting. Deburr all cut edges before reassembly.
❓ Will this shaft fit my tractor and peanut harvester?
Our PTO shafts are available with all standard yoke types and spline sizes (1-3/8" 6-spline, 1-3/4" 6-spline, 1-3/4" 20-spline, and more). Provide your tractor model and peanut harvester make/model, and our team will confirm compatibility before dispatch.
❓ Bagaimana cara mengukur panjang tertutup yang tepat?
Pasang alat pertanian ke traktor pada posisi kerja normalnya. Ukur jarak garis lurus dari permukaan poros PTO traktor ke permukaan poros input alat pertanian. Panjang poros saat tertutup harus sekitar 10–15 mm lebih pendek dari pengukuran ini.
❓ Garansi apa yang Anda tawarkan untuk poros PTO?
Semua poros PTO memiliki garansi pabrik terhadap cacat material dan pengerjaan. Ketentuan garansi berbeda-beda tergantung serinya. Hubungi tim kami untuk detail garansi spesifik yang berlaku untuk pembelian Anda.
❓ What PTO shaft series do I need for my peanut harvester?
For most peanut harvester applications in the 60–180 HP range, we recommend the T4 / L4 (Medium-heavy duty) or T5 / L5 (Heavy duty) series. If you operate near the upper end of this range or in particularly demanding conditions, consider stepping up to the S8 (Wide-angle) series for additional safety margin.
❓ Seberapa sering saya harus melumasi poros PTO?
Lumasi semua nipel sambungan U setiap 8–10 jam pengoperasian, atau di awal setiap hari kerja. Lumasi tabung profil teleskopik pada interval yang sama. Gunakan gemuk kompleks litium EP2 atau seperti yang direkomendasikan dalam manual produk Anda.
❓ Apa perbedaan antara baut geser dan kopling gesek?
Baut geser adalah pin pengorbanan yang patah ketika torsi melebihi kapasitas nominalnya. Harganya murah tetapi memerlukan penggantian manual setelah setiap kejadian. Kopling gesek selip ketika kelebihan beban dan secara otomatis terhubung kembali ketika kelebihan beban hilang, menawarkan pengoperasian tanpa gangguan dalam aplikasi yang rentan terhadap beban kejut yang sering terjadi.
Produk Terkait
Complement your Peanut Harvester PTO shaft with these products from our range:
Partner With Us – Peanut Harvester PTO Shaft Solutions
Whether you are a farmer seeking a single replacement shaft, a dealer looking to stock reliable driveline products, or an OEM manufacturer requiring bulk supply, we are ready to support your needs. Our peanut harvester PTO shafts are available in standard and custom configurations, with competitive pricing for volume orders.
📞 Hubungi tim kami hari ini Untuk mendiskusikan kebutuhan Anda, meminta penawaran harga, atau mengatur konsultasi teknis. Kami berkomitmen untuk memberikan poros yang tepat, tepat waktu, setiap saat.