High-Performance PTO Shaft for Hose Reel Applications
The hose reel irrigator relies on a consistent flow of rotational energy from the tractor’s PTO output to drive its working mechanisms. Our purpose-built PTO shaft for hose reel irrigator is designed to meet the demanding torque profiles and operational rhythms of travelling irrigation. Built for Australian conditions and available through ptoparts.top, this shaft delivers dependable performance from paddock to paddock.
Technical Specifications – Hose Reel PTO Shaft
| Parameter | Spesifikasi / Rentang yang Dapat Disesuaikan |
|---|---|
| Aplikasi | Hose Reel |
| Rekomendasi Tenaga Kuda Traktor | 30–90 HP |
| Kecepatan PTO | 540 rpm (Economy) |
| Torsi Kontinu Maksimum | 200–600 Nm |
| Kapasitas Torsi Puncak | 900 Nm |
| Seri Poros | T2 / L2 (Light-medium duty) / T3 / L3 (Medium duty) / T4 / L4 (Medium-heavy duty) |
| Diameter Tabung Luar | 65 mm |
| Profil Tabung | Square profile or Star profile |
| Maximum Extended Length | 1386 mm |
| Bahan Pelindung Keselamatan | HDPE (high-density polyethylene) / Injection-moulded PP (polypropylene) |
| Yoke Material | Forged alloy steel (42CrMo) |
| Kisaran Suhu Operasional | -30°C to +100°C |
| Universal Joint Cross Size | 22×54.8 mm / 34.9×93.1 mm / 23.8×61.3 mm |
| Closed Length (Lmin) | 700–1100 mm (customisable) |
| Warna Penjaga | Black |
| Perawatan Permukaan | Yellow zinc plated |
| Pelumas yang Direkomendasikan | NLGI #2 multi-purpose |
| Opsi Yoke Ujung Traktor | Plain bore yoke / Splined yoke (1-3/4″ 6-spline) |
| Berat Rakitan | 11–24 kg (varies by length) |
| Tube Wall Thickness | 3.0 mm |
Working Principle of the Hose Reel PTO Shaft
At its core, the PTO shaft is a torque conduit. It begins at the tractor’s PTO output—a splined stub rotating at a governed speed—and terminates at the hose reel irrigator’s input flange or spline. Between these two endpoints, the shaft must compensate for three-dimensional movement: fore-aft telescoping, vertical angularity, and lateral offset.
Two Cardan-type universal joints provide the angular flexibility, while the lemon, star, or triangular profile tube slides within its mating tube to manage length changes. In the context of travelling irrigation, this means the shaft continuously adapts as the tractor turns, undulates over terrain, or lifts the implement on its three-point hitch.
The hose reel irrigator receives this rotational input through a gearbox or directly to its functional mechanism. The PTO shaft’s torque limiter acts as a mechanical fuse—if the implement encounters an immovable obstruction, the limiter disengages or absorbs the shock before damage can propagate to the tractor’s drivetrain.
Core Advantages of Our PTO Shaft for Hose Reel
⚙ Alloy Steel Construction
Our hose reel irrigator PTO shaft uses high-grade alloy steel tubing and forged yokes, offering up to 40% longer service life than economy alternatives.
🔨 Quick-Fit Yoke Options
Choose from quick-release, plain bore, or splined yokes for rapid implement changeover—no tools required in most configurations.
🔒 Multi-Stage Protection
Select from shear bolt, friction clutch, or free-wheel overrunning clutch protection to match your specific operational risk profile.
⚖ Low-Maintenance Bearings
Sealed needle-roller bearings in every U-joint eliminate frequent greasing while maintaining smooth, low-friction rotation under heavy loads.
🛠 Custom Length Options
Available in standard and custom closed lengths, our shafts fit virtually any tractor-to-implement spacing without modification.
🌍 Australian-Tested
Every shaft design is validated under Australian field conditions—heat, dust, and long operating hours—before release to market.
Kompatibilitas Merek & Suku Cadang Pengganti
Kita PTO shaft for hose reel irrigator dirancang sebagai pengganti langsung untuk rakitan poros penggerak yang dipasok oleh Eurocardan, Bondioli & Pavesi, AgriCardan, PTOline, Walterscheid, Musangdan lain-lain. Kami menyediakan panduan referensi silang untuk membantu Anda mengidentifikasi poros yang tepat untuk peralatan Anda yang sudah ada.
⚠ Nama merek hanya dirujuk untuk tujuan identifikasi kompatibilitas silang. Kami tidak berafiliasi dengan, dan kami tidak mengklaim dukungan dari, merek-merek yang disebutkan. Semua merek dagang tetap menjadi hak milik dari pemiliknya masing-masing.
Suku Cadang & Aksesoris
Setiap komponen poros PTO kami tersedia secara individual: kit sambungan U, penyangga (ujung traktor dan ujung implement), tabung profil, pelindung keselamatan, rantai pelindung, pembatas torsi, dan kit bantalan. Ini berarti Anda dapat melakukan servis dan perbaikan poros Anda tanpa batas, sehingga mengurangi biaya kepemilikan jangka panjang.
Peraturan, Kepatuhan & Pertimbangan SEO Lokal
Standar Keselamatan Australia
All PTO shafts supplied for hose reel irrigator applications comply with AS 1121 (Power take-offs for agricultural tractors) and AS/NZS 4024.1 (Safety of machinery). Safety guards meet the guarding requirements of Safe Work Australia’s model WHS Regulations.
Kepatuhan CE & ISO
Fasilitas manufaktur kami memegang sertifikasi ISO 9001:2015. Rakitan poros dirancang sesuai dengan ISO 5673 (Traktor dan mesin pertanian – poros penggerak PTO) dan diberi tanda CE jika berlaku.
Persyaratan Negara Bagian & Wilayah
Peralatan yang digerakkan PTO di seluruh Queensland, New South Wales, Victoria, Western Australia, South Australia, dan Tasmania harus mematuhi kode praktik K3 setempat untuk mesin pertanian. Poros kami dilengkapi dengan semua pengaman dan dokumentasi keselamatan yang diperlukan untuk memenuhi kewajiban ini.
PTO Shaft Selection Guide – Hose Reel
Selecting the right PTO shaft for your hose reel irrigator is straightforward when you follow this step-by-step guide. Gather the information below before placing your order.
| Step | Action | Details for Hose Reel |
|---|---|---|
| 1 | Identify tractor PTO HP | Typical: 30–90 HP for this application |
| 2 | Confirm PTO speed setting | 540 rpm or 1000 rpm (check implement manual) |
| 3 | Measure closed length (Lmin) | 700–1100 mm |
| 4 | Count tractor PTO splines | 6-spline (1-3/8") or 6-spline (1-3/4") most common |
| 5 | Check implement input connection | Splined, keyed, or flanged input |
| 6 | Calculate torque requirement | 200–600 Nm |
| 7 | Select shaft series | T2 / L2 (Light-medium duty) or T3 / L3 (Medium duty) |
| 8 | Choose overload protection | Friction clutch recommended for hose reel irrigator |
📌 Need help? Hubungi kami for expert guidance.
Targeted Installation Procedure – Hose Reel PTO Shaft
⚠ Safety First: Disengage the PTO, switch off the engine, remove the ignition key, and allow all moving parts to come to a complete stop before working on the driveline. Wear appropriate PPE including close-fitting clothing and gloves.
Phase 1: Preparation
Lay out all shaft components and cross-reference against the packing list. Confirm the shaft series, closed length, and yoke specifications match your hose reel irrigator setup. Grease all U-joint nipples and slide the profile tubes back and forth several times to distribute lubricant.
Phase 2: Length Verification
With the hose reel irrigator hitched to the tractor in its normal operating position, measure the PTO-to-input distance. The shaft must have a minimum of 1/3 tube overlap at full extension and must not bottom out at the shortest position. Trim the tubes if the factory length requires adjustment (refer to cutting instructions in the product manual).
Phase 3: Tractor Connection
Push the tractor-end yoke fully onto the PTO stub. The quick-release collar should snap over the retaining groove. Pull back on the yoke to confirm it is locked. If using a plain-bore yoke, insert the shear pin and secure with a cotter pin.
Phase 4: Implement Connection
Connect the implement-end yoke to the hose reel irrigator’s input. If a clutch assembly is fitted at this end, ensure the clutch housing is oriented with the grease nipple accessible. Tighten any set screws to the specified torque.
Phase 5: Guard Fitting
Assemble the two guard halves around the shaft and clip together. Attach the anti-rotation chains: one chain to a stationary tractor point, one chain to the implement frame. Verify the guards spin freely by hand without contacting any part of the shaft or yokes.
Phase 6: Operational Test
Start the tractor, engage PTO at low idle, and run the hose reel irrigator unloaded for two to three minutes. Check for vibration, abnormal noise, or heat at the U-joints. If all checks pass, proceed to normal operating speed and begin field work. Re-torque all fasteners after the initial run-in period.
PTO Shaft Troubleshooting Guide for Hose Reel
⚠ Shaft will not telescope smoothly
Possible Cause: Korosi atau kotoran di dalam tabung profil; pelumasan yang tidak memadai.
Recommended Action: Bersihkan dan lumasi tabung profil; ganti jika terlihat goresan.
⚠ Excessive vibration during operation
Possible Cause: Worn U-joint cross bearings; shaft out of balance; excessive operating angle
Recommended Action: Replace U-joint cross kit; check yoke alignment; reduce operating angle to <25°
⚠ Heat build-up at U-joint
Possible Cause: Pelumasan tidak memadai; sudut operasi berlebihan; kerusakan bantalan.
Recommended Action: Segera lumasi sambungan U; kurangi sudut pengoperasian; ganti kit silang jika bantalan rusak.
⚠ Clicking or knocking noise at low speed
Possible Cause: Bantalan jarum sambungan U aus; dudukan longgar pada poros PTO
Recommended Action: Ganti rakitan sambungan U; periksa keausan spline dan mekanisme penguncian yoke.
⚠ Safety guard not rotating freely
Possible Cause: Bantalan pelindung macet; pelindung rusak atau tidak sejajar
Recommended Action: Ganti bantalan pelindung; luruskan atau ganti bagian pelindung; pasang kembali rantai dengan benar.
⚠ Implement speed inconsistent
Possible Cause: Poros PTO selip; spline aus; kopling terhubung sebagian
Recommended Action: Periksa pengait poros; ganti poros jika alur aus; setel atau ganti rakitan kopling.
⚠ PTO shaft disconnects during operation
Possible Cause: Kerah pengunci aus; alur penahan pada poros PTO rusak.
Recommended Action: Ganti dudukan pelepas cepat; periksa dan perbaiki alur poros PTO jika aus.
⚠ Overload clutch slipping under normal load
Possible Cause: Clutch plates worn or contaminated; incorrect torque setting
Recommended Action: Adjust clutch torque setting; replace clutch plates if worn or oil-contaminated
Case Studies – PTO Shaft for Hose Reel in Australia
Catatan lapangan dari tim teknik dan penjualan kami di seluruh Australia:
📍 Northam, WA – Phil Bennett
Tujuan: Outfitted a newly purchased second-hand hose reel irrigator with a reliable aftermarket PTO shaft
Masukan: “Saya memesan kit pengganti enam bulan kemudian dan tiba dalam waktu 48 jam. Produk hebat, layanan hebat, dukungan hebat.”
📍 Coffs Harbour, NSW – Sam Thornton
Tujuan: Upgraded overload protection from shear bolt to friction clutch for smoother travelling irrigation
Masukan: “Fitted perfectly to my hose reel irrigator with zero modification. The quality is noticeably better than the OEM shaft it replaced. I’ll be ordering more for my other implements.”
📍 Esperance, WA – Rick Dawson
Tujuan: Replaced a worn PTO shaft on a 3-year-old hose reel irrigator to restore full operating efficiency
Masukan: “Kopling gesek terintegrasi menyelamatkan gearbox saya ketika kami menabrak batu yang terkubur. Poros langsung terlepas dan terhubung kembali setelah halangan teratasi. Sangat berharga.”
📍 Colac, VIC – Dean Hartley
Tujuan: Membutuhkan poros dengan panjang khusus untuk jarak traktor-ke-peralatan yang tidak standar.
Masukan: “Pengiriman cepat ke wilayah regional Australia. Poros tiba dalam kemasan yang baik dan sambungan U-nya sangat halus. Sangat terkesan dengan kualitas pembuatannya.”
📍 Bathurst, NSW – Neil Ferguson
Tujuan: Mengganti poros yang berkarat akibat terpapar residu semprotan bahan kimia.
Masukan: “We run our hose reel irrigator hard across 2,000 hectares and this shaft hasn’t missed a beat after two full seasons. Exceptional value for money.”
Frequently Asked Questions – PTO Shaft for Hose Reel
❓ Bagaimana cara mengukur panjang tertutup yang tepat?
Pasang alat pertanian ke traktor pada posisi kerja normalnya. Ukur jarak garis lurus dari permukaan poros PTO traktor ke permukaan poros input alat pertanian. Panjang poros saat tertutup harus sekitar 10–15 mm lebih pendek dari pengukuran ini.
❓ Apa penyebab kegagalan sambungan U-joint sebelum waktunya?
Penyebab umum meliputi pelumasan yang tidak memadai, sudut pengoperasian yang berlebihan (lebih dari 25°), pengoperasian pada kecepatan lebih tinggi dari yang ditentukan, ketidaksejajaran antara traktor dan alat pertanian, dan kurangnya inspeksi rutin. Mengikuti jadwal perawatan yang direkomendasikan secara signifikan memperpanjang masa pakai sambungan U.
❓ Apakah Anda melakukan pengiriman ke wilayah regional dan terpencil di Australia?
Tentu saja. Kami mengirimkan ke semua kode pos Australia melalui perusahaan pengiriman barang utama. Daerah regional dan terpencil mungkin memiliki waktu transit yang sedikit lebih lama, tetapi kami bekerja sama dengan berbagai perusahaan pengiriman untuk memastikan pengiriman yang andal di seluruh negeri.
❓ Can the shaft be shortened to fit my setup?
Yes. The telescoping profile tubes can be cut to a shorter length using an angle grinder or chop saw. Ensure a minimum of 1/3 overlap remains between the inner and outer tubes after cutting. Deburr all cut edges before reassembly.
❓ What PTO shaft series do I need for my hose reel irrigator?
For most hose reel irrigator applications in the 30–90 HP range, we recommend the T2 / L2 (Light-medium duty) or T3 / L3 (Medium duty) series. If you operate near the upper end of this range or in particularly demanding conditions, consider stepping up to the S6 (Standard) series for additional safety margin.
❓ Seberapa sering saya harus melumasi poros PTO?
Lumasi semua nipel sambungan U setiap 8–10 jam pengoperasian, atau di awal setiap hari kerja. Lumasi tabung profil teleskopik pada interval yang sama. Gunakan gemuk kompleks litium EP2 atau seperti yang direkomendasikan dalam manual produk Anda.
❓ Will this shaft fit my tractor and hose reel irrigator?
Our PTO shafts are available with all standard yoke types and spline sizes (1-3/8" 6-spline, 1-3/4" 6-spline, 1-3/4" 20-spline, and more). Provide your tractor model and hose reel irrigator make/model, and our team will confirm compatibility before dispatch.
❓ Can I use a 540 rpm shaft on a 1000 rpm PTO?
No. Using a shaft rated for 540 rpm on a 1000 rpm PTO will result in excessive speed, dangerous vibration, and potential catastrophic failure. Always match the shaft speed rating to both the tractor PTO setting and the implement requirement.
Produk Terkait
Complement your Hose Reel PTO shaft with these products from our range:
Partner With Us – Hose Reel PTO Shaft Solutions
Whether you are a farmer seeking a single replacement shaft, a dealer looking to stock reliable driveline products, or an OEM manufacturer requiring bulk supply, we are ready to support your needs. Our hose reel irrigator PTO shafts are available in standard and custom configurations, with competitive pricing for volume orders.
📞 Hubungi tim kami hari ini Untuk mendiskusikan kebutuhan Anda, meminta penawaran harga, atau mengatur konsultasi teknis. Kami berkomitmen untuk memberikan poros yang tepat, tepat waktu, setiap saat.